Conversations

Conversations 1 - 20 of 22
Photo of Geoff - W8GNM
6600M bandwidth center/width controls
When the 6600M front panel filter controls are put into the "width / center" mode, the filter bandwidth collapses to zero bandwidth if th...
  • 1 me too
  • 7 replies
  • Problem
Photo of Rej va2am
6600(m) cw mode memory buffer
6600(M) stand alone, can we store short cw messages like Call 599 report for dx? or do we need to install a third party software? Thank...
  • 1 me too
  • 7 replies
  • Question
Photo of Jeremy Gilbert KC1JZE
Why does the Flex 6600 need band preselectors?
I’m loving my 6600 - an incredible instrument! As I dig deeper and deeper into the documentation and try to learn the art of SDR signal ...
  • 1 me too
  • 14 replies
  • Question
  • Answered
Photo of Geoff - W8GNM
6600 front panel power switch shutdown delay
Add two second delay to 6600 front panel power shutdown sequence? I have accidentally shutdown my Flex 6600 by inadvertently touching th...
  • 3 me toos
  • 1 reply
  • Idea
Photo of HCampbell  WB4IVF
Why I chose Power Genius XL & First Impressions
 I just replied to a question I received about my impressions of the PG XL.  Thought I’d share my thoughts with the group so below are ...
  • 5 me toos
  • 10 replies
  • Praise
Photo of Geoff - W8GNM
Memorize TX bandwidth?
Is it possible to have the memory locations memorize the TX bandwidth with upper and lower limits for each memorized frequency?   This wo...
  • 1 me too
  • 5 replies
  • Question
Photo of Geoff - W8GNM
60M operation with ver 2.3.9 software
TUNE and MOX functions are not working on all 60m channels using software version 2.3.9 running on Flex 6600M. Neither MOX or TUNE funct...
  • 1 me too
  • 3 replies
  • Problem
Photo of KF4HR
Adjusting waterfall height
Perhaps I've missed this in the manual, but when viewing one slice on the Maestro, is there a way to lessen the height of the waterfall d...
  • 3 me toos
  • 3 replies
  • Question
  • Answered
Photo of Geoff - W8GNM
Idea: Allow receiver passband to move through the carrier frequency in SSB mode
Idea: Allow the receiver to shift the passband through the carrier frequency in SSB mode When the 6600M's bandpass filter controls are pl...
  • 1 me too
  • 2 replies
  • Idea
Photo of Geoff - W8GNM
6600M connecting to SmartSDR CAT Application
If the 6600M has a LAN connection to the PC that the SmartSDR CAT application is running on at the time the 6600M is booted, the CAT appl...
  • 1 me too
  • 3 replies
  • Problem
Photo of Tim - W4TME
Please welcome Michael, VA3MW as Community Mayor Pro Tem
Starting tomorrow afternoon, I will be taking a temporary medical leave of absence for several weeks and Michael, VA3MW will be the Commu...
  • 8 me toos
  • 56 replies
  • Praise
Photo of Geoff - W8GNM
SmartLink control of remote 6700 from front panel of 6600M
My friend K8CJY and I tried several different configurations of SmartLink remote radio control. He was able to successfully login to my 6...
  • 1 me too
  • 2 replies
  • Question
Photo of Geoff - W8GNM
SmartSDR for iOS Locking Up On EQ Settings
I am using SmartSDR for iOS V1.2.8:0.50 Database VD1.28 (5.2.2018) with a Flex 6600M running radio software V 2.1.32.  The iPad is runnin...
  • 1 me too
  • 1 reply
  • Problem
Photo of Geoff - W8GNM
Flex 6600M making only 35W power output
Flex 6600M will only make 35W output power into a 50 Ohm load as measured by LP-100A calibrated wattmeter.  DC supply voltage is 13.8V un...
  • 1 me too
  • 5 replies
  • Problem
  • Solved
Photo of Geoff - W8GNM
Amplifier Keying Jacks no longer working on Flex6600M
My Flex6600M has been keying my amplifier normally using the TX1 RCA jack on the back panel to key the amplifier into transmit.   After b...
  • 1 me too
  • 7 replies
  • Problem
  • In Progress
Photo of Geoff - W8GNM
Login doesn't complete properly using Mozilla Firefox
I am having difficulty using Mozilla Firefox browser version 58.0.xx to login to my Flex community account.   When I login I get the succ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Geoff - W8GNM
Flex 6600M Rack Mounting Option Details
Is there any detailed information available for the Flex 6600M rack mounting option?A photo and/or a mechanical drawing with dimensions w...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Geoff - W8GNM
TX Input DAX sampling rate
The sampling rates for the I/Q DAX inputs are visible and adjustable.   What is the default sampling rate of the DAX Tx input?  Is it adj...
  • 1 me too
  • 2 replies
  • Question
Photo of Geoff - W8GNM
Flex 6600M Input and Output Impedance Specifications
I am in the process or integrating my new Flex 6600M into my ham shack.I need to know the input and output impedances of the audio I/O to...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Geoff - W8GNM
TCXO frequency calibration offset - Flex 6600M
I have an external Trimble Thunderbolt GPS frequency reference.   The Flex 6600M automatically detected its 10MHz precision frequency cor...
  • 1 me too
  • 3 replies
  • Problem
  • Acknowledged