Conversations

Conversations 1 - 20 of 373
Photo of W1MSG
Apple Airport Extreme
I am using an Apple Airport Extreme router and cant get a green light on the ports for Smartlink. I have entered them in the router confi...
  • 2 me toos
  • 7 replies
  • Question
Photo of W9ILY
Spots not in 2.3.9
I just upgraded to 2.3.9 and the spots that were appearing in 2.3.7 are no longer being received. The Telnet connection is feeding spots ...
  • 1 me too
  • 9 replies
  • Problem
Photo of Mark - WS7M
Spot API timestamp
Hi All, I've been working on my own software to deal with logging and spots.  I installed 2.3.9 so I have the latest spot fixes. I'm se...
  • 1 me too
  • 4 replies
  • Question
Photo of Ed, K0KC
SmartSDR 2.3.9 Network Disconnect
I appreciate the work that has gone into this latest release, but I can report that it apparently has not solved my random disconnect...
  • 1 me too
  • 6 replies
  • Problem
Photo of John, G3WKL
SmartSDR CAT v2.2.8 slice re-assignment problem
The logging program (Logger32 v3.50.356) that I use is linked to SmartSDR through COM4 port. Since using the latest versions of SmartSDR ...
  • 1 me too
  • 11 replies
  • Problem
Photo of Jay Spaulding
DAX V2.3.7 Error
I did the update this morning and now my DAX don't work. Shows Error on install. I tried multiple times. Even did it manual. Still dont w...
  • 1 me too
  • 4 replies
  • Question
Photo of Tim K9WX
AGC Slope
I’m two weeks and 500 QSOs into my Flex 6600 with a Maestro.  Most of those QSOs are CW with some FT8 and RTTY. I have a number of q...
  • 2 me toos
  • 6 replies
  • Question
  • Answered
Photo of Doug - K3TZR
API status message with incorrect frequency
When starting SmartSDR, If I monitor the status messages sent by the radio to SmartSDR the initial status message has the wrong frequency...
  • 1 me too
  • 1 reply
  • Problem
Photo of Robert Lonn
6600M, F1-F6 Front Buttons
F1 key stay lit when powered off! Today I set the F1 key for SAM and the F4 key for simple AM. I had it in the F1 on position, Lit Up,  b...
  • 1 me too
  • 8 replies
  • Question
Photo of KK9W - Steve
Upgrading Advantages
What would be the advantages of upgrading to a 6400 from a 6300. Differences??
  • 1 me too
  • 8 replies
  • Question
Photo of Johan SE3X
Flex 6500 and 6700 on the same network? Trying to get it to work.
Just about to set up my second Flex. First radio is a 6700 and now adding a 6500. Been scanning the community, finding a lot of info, bu...
  • 1 me too
  • 11 replies
  • Question
Photo of KB4OIF
message says the radio is in use then reboots
During our net this evening, my 6400M had a message come on the screen saying that the radio was in use, try again later.   It rebooted a...
  • 3 me toos
  • 26 replies
  • Problem
  • Acknowledged
Photo of NX6D Dave
M Series Radios start-up advice
There have been a few instances lately of M Series radios (6400M, 6600M) not starting up correctly.  These instances have sometimes left ...
  • 1 me too
  • 8 replies
  • Question
Photo of John G3WGV
Meter data duplicated?
For some time I've wanted to put some software damping on the S-meter to stop it bouncing around quite so wildly, so that took me into co...
  • 1 me too
  • 1 reply
  • Question
Photo of John - K3MA
No activity on spectrum or waterfall upon restart V2
I have noticed a glitch.  On a local LAN Flex 6500 running V2.  Sometimes when shutting down the software and restarting it there is no a...
  • 4 me toos
  • 11 replies
  • Problem
Photo of Matt NQ6N
Strange effects of dragging the panafall
I have noticed that when scrolling/dragging the panafall horizontally when zoomed out there are sometimes sudden changes in the amplitude...
  • 1 me too
  • 3 replies
  • Question
Photo of Wayne
What is this response telling me?
Playing with api sent command to change freq to 14.245 but did not change and returned this message ... what is the radio telling me ... ...
  • 1 me too
  • 6 replies
  • Question
Photo of Wayne
Response Time to Sucessful Connection
I can receive the discovery packet or packet(s) if desired and I have decoded and parsed the information then used it to establish a conn...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of N4FP
Flex 6400 “Excess power detected on receiver” error message
I have encountered an unusual situation with my new Flex 6400 received last week.  Please bear with me, my explanation is a bit complic...
  • 1 me too
  • 13 replies
  • Problem
  • Solved
Photo of Matt NQ6N
Is keying possible via the API or CAT/Serial (RTS or DTR)?
I'm wondering if it is possible to key the 6600 directly via the API (TCP) CAT, or Serial (RTS/DTR) methods.  I know it is possible to se...
  • 1 me too
  • 5 replies
  • Question
  • Answered