Conversations

Conversations 1 - 20 of 22
Photo of Hel, OE8TTR
How loud is the 6600?
Hello, being a Flex-6500 user, I'ld like to upgrade for a 6600 BUT before I do this, I'ld like to know about the fan-noise from the 6600....
  • 1 me too
  • 19 replies
  • Question
Photo of Michael Walker
6000 Series and ALS-1306 Amp
All I want to confirm something for a customer, and that is the exact setup for a Serial connection to a ALS-1306. From what I can dig ...
  • 3 me toos
  • 14 replies
  • Question
Photo of Ed N5DG
What is Eric KE5DTO E-mail address
I have a simple question for FRS and would like to send an e-mail to Eric KE5DTO Tnx Ed N5DG
  • 1 me too
  • 2 replies
  • Question
Photo of Ed N5DG
6600 M using the 2 USB ports ?
Will the two USB ports on the back of the 6600M support the USB to serial FTDI drivers without connecting to a computer using SSDR  ?Than...
  • 1 me too
  • 4 replies
  • Question
Photo of Ed N5DG
RadioSetup Settings , How do I save ?
Flex 6600 , I am trying to change some settings in  the radiosetup panel. Specifically saving setting the RCA TX to enable and the TX Del...
  • 1 me too
  • 9 replies
  • Question
Photo of N5CQ
Can't transmit FT8 Using Smartlink
Installed SmartSDR 2.4.9 with no problems, SSB and CW work fine, now trying FT8. Transmit works fine in CW and SSB, as does TUNE in SSDR....
  • 2 me toos
  • 8 replies
  • Question
Photo of Ed N5DG
Should my 6600 flash red 1 time ?
I leave my 6600 on most of the time but today I've cycled it on and off a few time and see it flashes red once before starting the green ...
  • 1 me too
  • 8 replies
  • Question
Photo of Ed N5DG
where is the link to summit help with broke 6600
How do I summitt a help ticket ? Ed N5DG
  • 1 me too
  • 2 replies
  • Question
Photo of Ed N5DG
Trouble with SSB , must go to CW and back to SSB for SSB to work
Flex 6600 dos not transmit in SSB mode until I change to CW , tape the paddle and then change back to SSB ... Now I can use SSB .! The sa...
  • 2 me toos
  • 3 replies
  • Problem
Photo of Al / NN4ZZ
CW Filter Widths in the "RX Display Tab" -- 250 is missing
I think most CW operators primarily use the narrow filters widths between 50 and 250.  There are 8 to choose from in the "slice display" ...
  • 10 me toos
  • 12 replies
  • Idea
Photo of Andrew - G0RVM
Slicemaster v0.10.5d Launch tab empty
I've installed Slicemaster and it seems to run ok (it doesn't report errors and seems to connect to a specified cluster server ok), but t...
  • 1 me too
  • 9 replies
  • Problem
Photo of Sergey Abrikosov
FTDI USB-Serial adapter question
I do not think it is Flex related question, but decided to ask here anyway.I have several FTDI adapters and used them without any issue l...
  • 1 me too
  • 9 replies
  • Question
Photo of Ed - W2RF
New CW Skimmer v2.1 and SDR-Bridge v1.6.4
Initial testing of SDR-Bridge v1.6.4 with the new v2.1 of CW Skimmer looks good. Let me know of any issues either here or at the web site...
  • 1 me too
  • 2 replies
  • Idea
Photo of Mark WS7M
6600 Fan - Disappointed
Ok, so I sent my 6600 in for the PEN update.When it came back it rebooted continuously.  After looking inside I could hear the fan runnin...
  • 1 me too
  • 23 replies
  • Problem
  • Solved
Photo of Andrew Thall
Great customer service
Tim Ellison, W4TME, Customer Experience Manager, gave me great service in helping me figure out what went wrong with my 6300 -- which is ...
  • 7 me toos
  • 1 reply
  • Praise
Photo of Ed N5DG
Flex 6600 to SPE Expert amp, help me understand
New guy with questions again, I would like my SPE 2KFA Amp to follow my new 6600 . I need some help understanding how the cabling works ....
  • 1 me too
  • 3 replies
  • Question
Photo of Ed N5DG
Newbie question , Looks like I QRM second slice ?
I have slice A on 50,098 CW and slice B on 50.313 FT8 . When I tune or use the paddle on Slice A , I see spikes or interference on slice ...
  • 1 me too
  • 8 replies
  • Question
Photo of Geert Balsma PA3CPS
SDR settings for SPE 1.3K amplifier
I want to connect my new SPE expert 1.3K to my Flex 6500. I have already Dan's (KC5PCB) cable set. Can someone tell me what i have to cha...
  • 1 me too
  • 17 replies
  • Question
  • Answered
Photo of Ed N5DG
Can't fine CWX in SSDR
I've looked in the manual for CWX but I have overlooked it somehow , The user guide I downloaded is for the 6600M and the 6400M , My radi...
  • 1 me too
  • 2 replies
  • Question
Photo of Ed N5DG
problem getting Winkey working wint N1MM / SSDR
I'm new to SSDR / Flex 6600 . I'm having a problem getting Winkey USB to connect with N1MM and SSDR CAT . I've used Winkey /N1MM on a dif...
  • 1 me too
  • 3 replies
  • Question