Conversations

Conversations 1 - 20 of 538
Photo of Ed N5DG
Flex 6600 to SPE Expert amp, help me understand
New guy with questions again, I would like my SPE 2KFA Amp to follow my new 6600 . I need some help understanding how the cabling works ....
  • 1 me too
  • 3 replies
  • Question
Photo of Geert Balsma PA3CPS
SDR settings for SPE 1.3K amplifier
I want to connect my new SPE expert 1.3K to my Flex 6500. I have already Dan's (KC5PCB) cable set. Can someone tell me what i have to cha...
  • 1 me too
  • 17 replies
  • Question
  • Answered
Photo of IZ2ODM
USB port hooked with ACOM 2000A
Hello ; I've just hooked the CAT port of the (rear 15 P) consolle of ACOM 2000A with USB port trought USB FTDI genuine cable (immediately...
  • 1 me too
  • 15 replies
  • Question
  • Answered
Photo of KK9W - Steve
Zoom to Segement
So what exactly is this zoom to segment supposed to do???
  • 1 me too
  • 7 replies
  • Question
Photo of Paul
SmartLink - how many simultaneous clients?
My primary interest in the Flex 6xx is WAN remote. Does anyone know if: 1) SmartLink will support more than one connection simultaneou...
  • 1 me too
  • 6 replies
  • Question
Photo of Ken, K2KXK
Smartlink stopped working today
Have been using Smartlink every day since I got my 6300 about a month ago. Stopped working this morning. Thought it might be a temporary...
  • 1 me too
  • 7 replies
  • Problem
Photo of Neil   N4FN
PEN Heat sink replacement
What a classy company. My kit arrived on Friday and it took longer to remove the 14 Torx screws than the update took. I followed the inst...
  • 1 me too
  • 9 replies
  • Praise
Photo of David Decoons wo2x
SmartLink problems traced to cable modem using Intel PUMA 6 chipset
Since the inception of SmartLink I have always noticed "pops" or "clicks" in both receive and transmit audio when running remote. Both on...
  • 5 me toos
  • 2 replies
  • Praise
Photo of Rick  WN2C
13 Colonies Special Event 2018
Well the event is over and I was able to make a Clean Sweep of all 13 Colony stations. Some were difficult to pull out but the Flex 6400M...
  • 1 me too
  • 6 replies
  • Praise
Photo of Homer1952
Clean transmitter
There are a lot of things I'd like for Flex to improve.  But one thing they have nailed is very low IMD on transmit.  When I see a Flex 6...
  • 3 me toos
  • 4 replies
  • Praise
Photo of Michael Coslo
PW-1 and ALC
I have my Flex 6300 bandswitching with my PW-1 Amplifier using Ed W2PH's bandswitching box. But now I have a question about the ALC from ...
  • 1 me too
  • 3 replies
  • Question
Photo of Tom Teague
Heatsinks are falling off in 6400 and 6600 models.
As part of the Product Enhancement Notification (PEN) or Recall.  If you want to know where to look to see if both of your heatsinks are ...
  • 4 me toos
  • 48 replies
  • Problem
  • In Progress
Photo of Amlan - AI6XN
A conversation needed pre purchase
I am moving into Flex 6600M from being an avid ICOM 7610 user and I feel for people like us, the first time converts to flex,there should...
  • 2 me toos
  • 11 replies
  • Idea
Photo of Roger J. Buffington
Question about WSJT-X "split" setting with Flex 6400
In the WSJT-X configuration "Radio" tab there is a "Split" option with choices of either "none", "rig" or "fake it."  The latter two choi...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Mike
something isn't quite right in FT8
I cannot seem to hear KH1 on 14090. I can see print from them 700 to 900 Hz below (14089.1). I've run calibrate. I'm not really sure what...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Albert PA0A
Help needed to get SmartLink connected to ASUS LTE.
I am using an ASUS 4G AC55U LTE, this is a radio router/modem operating via the LTE network. Nowhere in the settings UPnP is mentiond and...
  • 1 me too
  • 3 replies
  • Question
Photo of Bill -VA3WTB
Can someone tell me what the set up settings are for the Flex 6500 and the KPA 1500 amp?
Like baud rate, stop bit? things like that.
  • 1 me too
  • 4 replies
  • Question
Photo of Neal Pollack, N6YFM
Share: What's Your Battery Pack?
Since the Flex list of Maestro battery packs is short and contains some that no longer are available, I thought we should build a current...
  • 3 me toos
  • 9 replies
  • Question
  • Answered
Photo of Luigi Verdicchio
info upgrade
hi from italy owner of a flex6400 for a few hours. I noticed that I can not install an external video because the dedicated input is miss...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Jim Runge
Power Genius with 2.3.7
Updated to 2.3.7 and have lost my Standby/Operated button below the amp meters.  I see that the amp swr meter also changed so the 1.2 is ...
  • 1 me too
  • 1 reply
  • Question