Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Flex 6500 displays transverter IF on panadapter, not RF...Anyone else seen it?
Paul Bradbeer
Member
Not new to transverters, and have set up my 6500 as per SSDR user guide, but for some reason when you slept the band (144 MHz), the panadapter displays IF frequencies, not RF. Only way to overcome it is to type the RF value in to a slice Rx. Using latest version of SSDR, no other problems obvious. Ideas please!?
1
Comments
-
I think that is normal - I set up my kuhne 4m tvtr with my 6500 after some period on my 6300 and it puzzled me too second time round but after putting the correct rf freq in once it comes up as 70mhz each time now.
73
Steve gw0gei
0 -
Check the XVTR tab in Radio Setup
0 -
Thanks for reply, Steve. Seems a bit odd, and no mention of that in SSDR...ho hum.. BTW like your profile pick - I'm just back from a week's sport climbing trip in Kalymnos0
-
Ross, thanks for your reply. I did that, and double checked...nothing wrong with the Xvtr tab settings.0
-
Its a defect ... same here .. whenever I set up a new transverter I just set the RF frequency first after opening the first slice. I think this has been open for a long time .. sure I read about this before
0 -
Thanks, Simon. I did a search but didn't find anything....perhaps I didn't go back far enough. Given the prominence of transverter support in the 6000series, I hope it'll get sorted soon.0
-
I have entered this problem report into our bug tracker for additional investigation. Thank you for the defect report.
1
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 747 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 722 Genius Products
- 388 Power Genius XL Amplifier
- 250 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software