Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
clicking relay?
Options
WQ5C
Member ✭✭
I've noticed on several occasions that a relay clicks in & out on a regular basis while the radio is not in use. Most recently, the radio has been powered up for about an hour, but I have not connected with SSDR yet. (F6500 & v1.0.0). I did not notice this with prior software/firmware versions. Any idea what's happening here?
0
Comments
-
I had some time to play with this. The clicking now starts up almost immediately after power on, and is now clicking constantly every 3 seconds or so. On CW I can hear a shift in the RX tone. Resetting to factory defaults didn't clear it. Should I open a support ticket?0
-
I have noticed that when powering on the radio and it completes the calibration mode, sometimes a Relay will click and make the FLEX go into a "MOX" mode. To get the FLEX to not KEY UP, I have to quickly selecty the FLEX (MOX Button) to get it to switch back to regular receive mode. When the relay is holding the FLEX in KEY UP mode, I still receive normally. This just started after loading the latest SmartSDR 1.0 upgrade.0
-
Thanks for the reply, but I don't think that's what I'm seeing. The radio is not transmitting during these episodes. I just hear a relay click in and out every few seconds and the RX shifts frequency slightly. It get *really* annoying after a few minutes. No one else is seeing this behavior?0
-
I did but not consistantly. It seems like one of those things that fixes itself with a reset of the power to the radio for about 30 seconds. It eventually comes back but I don't know what causes it.0
-
Mike, I have changed your question topic to to a problem. I have also transferred it to the HelpDesk as a support ticket for resolution.0
-
Thanks Tim. I think I may know what's happening here. I'm using an external GPSDO 10MHz source. I suspect the radio doesn't like it, and is switching between the internal & external reference. That would explain everything. I'll follow up with the helpdesk.0
-
This topic has been solved in Zendesk0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.3K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 343 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 726 Genius Products
- 391 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 221 Shack Infrastructure
- 149 Networking
- 369 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 810 Third-Party Software